Deletion sequences
The target chain with one amino acid missing somewhere along it. They are often the closest neighbors of the main peak on HPLC.
(“im-PYOOR-ih-teez”)
What the other 1 to 2% of a 98% pure peptide actually is.
The short answer
Impurities are everything in a peptide material that is not the intended sequence, from closely related peptide variants to residual water and counter-ions.
Peptide-related impurities are variants of the target that differ by a residue, a bond or a few atoms, such as a sequence missing one amino acid, an oxidized form or a deamidated form. Non-peptide content, such as water and counter-ions, is measured separately. HPLC shows peptide-related impurities as peaks beside the main peak, and LC-MS identifies them by mass.
Reviewed by the Codex Research quality teamUpdated Nov 8, 2026
Word study
Say it
im·pu·ri·ties
(“im-PYOOR-ih-teez”)
Roots and origin
RootLatin
OriginLatin
An impurity is literally a state of not being clean or unmixed. In analytical chemistry the word is neutral: it names any component other than the one intended, without saying whether it matters.
Around the world
Tap a language to hear it spokenDefinition
Every peptide material contains something besides the target sequence. The question is never whether impurities exist but what they are, how much of each there is, and whether the method used could see them. A purity result is really a statement about impurities: 98% purity means about 2% of the peptide signal belongs to something else.
Peptide-related impurities are the hardest to separate because they look so much like the target. Reviews of peptide quality group them into a few families: sequences missing one or more residues, chains that stop short, extra residues, residues in the wrong stereochemical form, and products of degradation such as oxidation and deamidation. Most differ from the target by a single residue or a handful of atoms.
Non-peptide content is a separate matter. Water, counter-ions such as acetate or TFA, and traces of solvents are part of the powder’s weight but do not show up as HPLC impurity peaks. They are measured by other methods, such as Karl Fischer titration for water, and are captured by net peptide content rather than HPLC purity.
Detection and identification are two steps. HPLC with UV detection shows impurities as peaks and measures their share of the total area. LC-MS then gives each peak a mass, which usually reveals what it is: a mass 16 Da higher points to oxidation, a mass lower by the weight of one residue points to a deletion. Studies that tested research-grade peptides bought from different suppliers found impurity profiles that were often more complex than the stated purity suggested.
Regulated peptide products work with defined thresholds. FDA guidance for certain synthetic peptides, for example, discusses identifying and characterizing peptide-related impurities at levels of 0.10% and above relative to a reference product. Research-grade certificates rarely go that far, but the principle is useful: a good certificate shows how impurities were measured, not just a single purity figure.
Common kinds
The target chain with one amino acid missing somewhere along it. They are often the closest neighbors of the main peak on HPLC.
Chains that stop before the full length, missing several residues from one end. Usually easier to separate than single deletions.
The target with oxygen added to a sensitive residue, most often methionine. Can form during manufacture or storage.
Asparagine or glutamine converted to an acidic residue. The mass barely changes, but the charge does.
The same sequence with one residue in the D instead of the L form. Same mass, so only a capable separation can show it.
For buyers
The purity figure on a certificate is defined by what the method counted as not the target. Knowing the impurities is knowing what the number means.
The impurities most likely to be missed are the ones that look most like the target, differing by a single residue or a few atoms.
LC-MS turns anonymous peaks into named variants, which shows whether a method separated what it needed to separate.
At Codex Research
Each Codex Research product page carries a lot-matched certificate of analysis reporting HPLC purity and mass spectrometry identity for the lot in stock.
See it live: the chromatogram guide, with a simulated impurity profile
Myth vs fact
Tap a card to flip it.
Watch for
Quick check
HPLC with a stated wavelength, ideally with a chromatogram attached.
Several small peaks with area % values, not a lone 100%.
A mass spectrometry result that matches the expected mass.
Full walkthrough · JournalPeptide purity grades explainedQuestions
Anything in the peptide material other than the intended sequence, from closely related peptide variants to non-peptide content such as water.
Deletion and truncated sequences, oxidized and deamidated forms, and stereochemical variants, plus water and counter-ions outside the peptide signal.
HPLC measures each impurity peak as a share of the total area. LC-MS identifies peaks by their mass.
About 2% of the peptide signal on the HPLC trace comes from components other than the target sequence.
Impurities are a quality measure. Whether a given impurity matters depends on what it is and how much is present, which is why it is measured and reported.
A version of the target peptide missing one amino acid. It is usually one of the hardest impurities to separate from the main peak.
Research certificates usually report total purity. Individual impurities are listed when a method reports them above a set threshold or when a buyer asks for the profile.
Sources and standards
Written and reviewed by the Codex Research quality team · Last reviewed November 8, 2026 · For laboratory research use only.
On real products
These products’ current certificates report purity by RP-HPLC, the method behind impurities. See the result on each product page, then read the full guide.
CellularResearch peptide
Neuropeptide Research
VIP is a 28-residue neuropeptide of the secretin/glucagon superfamily that acts at the VPAC1 and VPAC2 receptors, studied in class B GPCR research.
GH axisResearch peptide
GH-Axis Research
CJC-1295 without DAC is modified GRF(1-29) carrying four substitutions at positions 2, 8, 15 and 27 that resist the plasma enzyme cutting native GHRH.
CellularResearch peptide
Cellular Research
SS-31 (elamipretide) is a synthetic tetrapeptide that binds cardiolipin at the inner mitochondrial membrane, studied in bioenergetics and oxidative-stress research.
Journal guidePeptide purity grades explainedRead the guide
From lab to your door
U.S.-made research vials, shipped with lot-matched, lab-tested COAs you can scan straight off the label.
21+ Only
Codex Research provides research-grade compounds for laboratory and research use only. By entering, you confirm you are at least 21 and agree to our Terms & Conditions.
By proceeding you affirm the statements above are true. Products are supplied for laboratory research use only — not for human or veterinary use, not for use in diagnostic procedures, and not evaluated by the U.S. Food and Drug Administration. Full disclaimer.